Rabbit RCM3200 Manuel d'utilisateur Page 41
- Page / 128
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
User’s Manual 35
6. USING THE TCP/IP FEATURES
6.1 TCP/IP Connections
Programming and development can be done with the RCM3200 RabbitCore modules
without connecting the Ethernet port to a network. However, if you will be running the
sample programs that use the Ethernet capability or will be doing Ethernet-enabled devel-
opment, you should connect the RCM3200 module’s Ethernet port at this time.
Before proceeding you will need to have the following items.
• If you don’t have Ethernet access, you will need at least a 10Base-T Ethernet card
(available from your favorite computer supplier) installed in a PC.
• Two RJ-45 straight through Ethernet cables and a hub, or an RJ-45 crossover Ethernet
cable.
The Ethernet cables and a 10Base-T Ethernet hub are available from Rabbit Semiconduc-
tor in a TCP/IP tool kit. More information is available at www.rabbit.com.
NOTE: Although 10Base-T is the minimum required, 10/100Base-T or 100Base-T is
recommended to allow you to work with the full speed capabilities of the RCM3200.
1. Connect the AC adapter and the programming cable as shown in Section 2.2.2, “Con-
nect Programming Cable.”
2. Ethernet Connections
There are four options for connecting the RCM3200 module to a network for develop-
ment and runtime purposes. The first two options permit total freedom of action in
selecting network addresses and use of the “network,” as no action can interfere with
other users. We recommend one of these options for initial development.
• No LAN — The simplest alternative for desktop development. Connect the
RCM3200’s Ethernet port directly to the PC’s network interface card using an RJ-45
crossover cable. A crossover cable is a special cable that flips some connections
between the two connectors and permits direct connection of two client systems. A
standard RJ-45 network cable will not work for this purpose.
• Micro-LAN — Another simple alternative for desktop development. Use a small Eth-
ernet 10Base-T hub and connect both the PC’s network interface card and the
RCM3200’s Ethernet port to it, using standard network cables.
- RabbitCore RCM3200 1
- Rabbit Semiconductor Inc 2
- Trademarks 2
- TABLE OF CONTENTS 3
- Appendix D. Power Supply 103 5
- Notice to Users 115 5
- Index 117 5
- Schematics 121 5
- 1. INTRODUCTION 7
- Table 1. RCM3200 Features 8
- User’s Manual 3 9
- 1.4 How to Use This Manual 10
- 2. HARDWARE SETUP 11
- Do not press down 12
- PC COM port 13
- 8 RabbitCore RCM3200 14
- 2.3 Run a Sample Program 15
- 2.4 Where Do I Go From Here? 16
- 3. RUNNING SAMPLE PROGRAMS 17
- 3.2 Sample Programs 18
- User’s Manual 13 19
- 14 RabbitCore RCM3200 20
- 4. HARDWARE REFERENCE 21
- Headers J1 and J2 are 22
- Backup Battery 23
- 18 RabbitCore RCM3200 24
- User’s Manual 19 25
- 20 RabbitCore RCM3200 26
- User’s Manual 21 27
- 4.2 Serial Communication 28
- DIAG connector on 29
- LNK), one to 29
- ACT), and one to indicate 29
- 4.3 Serial Programming Cable 30
- 26 RabbitCore RCM3200 32
- 4.4 Other Hardware 33
- 4.5 Memory 34
- 5. SOFTWARE REFERENCE 35
- 30 RabbitCore RCM3200 36
- 5.2 Dynamic C Function Calls 37
- RS232.LIB 38
- PACKET.LIB 38
- User’s Manual 33 39
- RETURN VALUE 39
- 5.3 Upgrading Dynamic C 40
- 6. USING THE TCP/IP FEATURES 41
- 36 RabbitCore RCM3200 42
- User’s Manual 37 43
- 38 RabbitCore RCM3200 44
- User’s Manual 39 45
- 40 RabbitCore RCM3200 46
- User’s Manual 41 47
- 42 RabbitCore RCM3200 48
- User’s Manual 43 49
- User’s Manual 45 51
- 46 RabbitCore RCM3200 52
- 6.7 Where Do I Go From Here? 53
- 48 RabbitCore RCM3200 54
- User’s Manual 49 55
- Please refer to the RCM3200 56
- Exclusion 57
- 52 RabbitCore RCM3200 58
- User’s Manual 53 59
- A.2 Bus Loading 60
- I/O read and write cycles 61
- 56 RabbitCore RCM3200 62
- = –55°C to +125°C, V 63
- = 3.0 V to 3.6 V 63
- 58 RabbitCore RCM3200 64
- A.5 Conformal Coating 65
- A.6 Jumper Configurations 66
- PPENDIX B. PROTOTYPING BOARD 67
- B.1 Introduction 68
- User’s Manual 63 69
- 64 RabbitCore RCM3200 70
- User’s Manual 65 71
- B.3 Power Supply 72
- User’s Manual 67 73
- MEASUREMENT 74
- Connector Pinout 75
- Prototyping Board 76
- User’s Manual 71 77
- 72 RabbitCore RCM3200 78
- PPENDIX C. LCD/KEYPAD MODULE 79
- 74 RabbitCore RCM3200 80
- Contrast 81
- Adjustment 81
- C.3 Keypad Labeling 82
- C.4 Header Pinouts 83
- 78 RabbitCore RCM3200 84
- User’s Manual 79 85
- Bezel/Gasket 86
- User’s Manual 81 87
- C.7.3 LCD Display 89
- STDIO string functions 95
- C.7.4 Keypad 104
- library 104
- C.8 Sample Programs 107
- 102 RabbitCore RCM3200 108
- APPENDIX D. POWER SUPPLY 109
- 165 mA·h 110
- D.2 Optional +5 V Output 110
- E.1 Overview 111
- E.2 Header J6 112
- E.3 Using Parallel Port F 113
- 108 RabbitCore RCM3200 114
- Bits Value Description 115
- Table E-3. PWM Outputs 116
- E.5 PWM Registers 117
- E.6 Quadrature Decoder 118
- Rejected 118
- Accepted 118
- Peri Clock 118
- Timer A10 118
- User’s Manual 113 119
- 114 RabbitCore RCM3200 120
- NOTICE TO USERS 121
- 116 RabbitCore RCM3200 122
- User’s Manual 117 123
- 118 RabbitCore RCM3200 124
- User’s Manual 119 125
- 120 RabbitCore RCM3200 126
- SCHEMATICS 127
Produits connexes et manuels pour Cartes mères Rabbit RCM3200
Cartes mères Rabbit RCM2000 Spécifications
(40 pages)
(40 pages)
Cartes mères Rabbit RCM3000 Spécifications
(44 pages)
(44 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.138 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels